"Slightly Less Than Perfect" -- Semi-Circle Grommet Handles

Regular Price
$11.00 USD
Sale Price
$11.00 USD
Regular Price
Sold Out
Unit Price
per 
Finish: Glossy Nickel
Quantity
- +

Details

 

Even though these Semi-Circle Metal Grommet Handles are slightly less than perfect, they are still stunning and perfect for your project.

Their smooth and sleek luxury finish will definitely provide a professional appearance for your handbag or clutch.  They smooth inner top-bar provides a comfortable grip in your hand unlike other similiar shaped designs and the glossy finish provides a lustrous shine.

Please Note:  This listing is for the Semi-Circle Metal Grommet Handles that are sample quality and are not perfect.  These have very minor scratches or may have indents that were plated over as shown in the pictures below, which is why they are marked for immediate sale.  There are limited quantities of this item.

**** These are a Final Sale item and have been priced accordingly.  They cannot be returned as "defective".

 

Things to Consider:  These grommet handles are different than most other styles as the handle sits on the top edge of your bag and are heavy.  It is highly suggested to reinforce the area where the handle is to be installed with Peltex, Bontex or a firm stabilizer to provide a reinforced area for the handle, as it will be bearing the weight of the bag and its contents.  You must also consider that the exterior of your bag must have the strength to hold the handles upright, so if you using fabric or a soft temper leather/vinyl, you may want to line the entire bag with a stabilizer to provide additional strength.

They are sold in a set of two handles (one pair) and are installed with the 12 included screws. Each handle weighs approximately 140g with the two handle set being ~280g (9.5oz).  These handles also have tiny teeth on the backplate to "grab" ahold of the bag substrate which also provides added security to prevent the bag from separating from the handle. 

Please also use glue that bonds metal to fabric, vinyl or leather, such as HT2 Guttermann or E6000, to ensure that the metal adheres to your fabric or leather for a stronger hold.

Please Note:
The back of these handles have raised screws which will scratch and/or gouge the smooth front surface if stored incorrectly. 
These must be packaged and stored in the manner in which they were sent.  The Smooth Side facing outwards and the backside of the handles back to back with its matching pair so that the screws are facing each other.
 

Installation Instructions:  This handle will require a semi-circle to be cut out from the center of the bag much like you would install a grommet.  It is advised to leave the poly-film on your hardware front to prevent scratching.

  • Remove the back plate of the handle along with the screws.  You will be using the back-plate inner edge as your hole guide.
  • Rest the top edges of the back-plate along the the top edge of your bag.  Be sure to center the template with the center of your bag.
  • Once placement has been decided, trace the inner semi-circle shape onto your bag exterior and mark your screw holes.  
  • Carefully cut out the semi-circle shape with scissors and make your screw holes using a punch or awl.  You will want to double check the "fit" of the handle in case you need to snip a little extra away from the inner cutting of your bag, and to ensure that the screw holes and posts line up. Make adjustments as required.
  • Once satisfied with the "fit", apply Fray Check or something similar to seal your fabric edges to prevent tiny fibers from poking out of the grommet handle edges.
  • If using glue, cover the back of the grommet handle channels with adhesive and put into place on the front of your bag.  Make sure that any stray fibers are tucked away inside the handle and not hanging out beyond the metal channel.  Then apply adhesive to the back of the back-plate, and place on the inside of your bag, while matching up all screw holes and inner channel.
  • Re-install the screws.  You may also want to add an adhesive to the screw hole prior to replacing the screws.  Loc-Tite or another adhesive such as E6000 works well.

 

Dimensions (Approximate):
Outside Dimensions: 150mm wide x 70mm high (6" wide x 3" high)
Inner Dimensions:  100mm wide x 55mm high (4" long x 2.25" high)